gfxgfx
 
Please login or register.

Login with username, password and session length
logo
 
gfx gfx
gfxgfx
 



Updates
Latest oscam all images 11756 (update) 28-03-2024
Vu+ Pur E2 7.3 & 7.4 (update) 19-03-2024
Dreambox Pur E2 7.3 (DM 900 & 920) (update) 19-03-2024
LuxSat Key Files update by MOHAMED_OS 18-03-2024


Donation also possible by bank transfer Click here
Your donation will help keep the site running
To view all topics you must be registered and logged in
 
gfx gfx
gfx
72179 Posts in 11153 Topics by 6350 Members - Latest Member: Ghassemi March 28, 2024, 01:04:24 PM
*
gfx* Home | Help | Login | Register | Home | Contact | Translation | gfx
gfx
LuxSat Satellite  |  Satelliet Programmer  |  Software  |  Waar kan ik de driver voor een smargo usb smartreader vinden aub?
gfx
gfxgfx
 

Author Topic: Waar kan ik de driver voor een smargo usb smartreader vinden aub?  (Read 3886 times)

0 Members and 1 Guest are viewing this topic.

Offline jpdc1991Topic starter

  • Bronze Member
  • *
  • Posts: 259
  • Country: 00
Hallo,
Ik ben op zoek naar een driver die kompatiebel zou zijn om mijn smargo smartreader om hem te kunnen gebruiken onder ubuntu server 6.10 :-D
Kan iemand mij raad te geven aub?  :?

Offline Jack Daniels

  • Bronze Member
  • *
  • Posts: 517
Re: Waar kan ik de driver voor een smargo usb smartreader vinden aub?
« Reply #1 on: April 29, 2008, 02:13:02 PM »
Kan je hier wat mee?
Hierbij de howto in het Engels. Op een Fedora server werkt het op deze manier

1: Linux PC setup.
Make sure that your installed linux distro wich has kernel 2.6.12 or newer version!

2: Update your smartreader+ if it has v1.2 or older firmware with v1.3

3: Before update make sure your reader is 100% reconized by linux!
You will find inside that "smartreader_v103.zip" very precise how to update that device. Now disconnect smartreader+ disable from CCcam smartreader+ config lines and make restart to linux PC. If linux is UP plug smartreader to USB and wait little so 20 second. Log to server and tipe command: dmesg
you should have like this:
usb 1-1: new full speed USB device using uhci_hcd and address 2
usb 1-1: configuration #1 chosen from 1 choice
usbcore: registered new driver usbserial
drivers/usb/serial/usb-serial.c: USB Serial support registered for generic
usbcore: registered new driver usbserial_generic
drivers/usb/serial/usb-serial.c: USB Serial Driver core
drivers/usb/serial/usb-serial.c: USB Serial support registered for FTDI USB Seri al Device
ftdi_sio 1-1:1.0: FTDI USB Serial Device converter detected
drivers/usb/serial/ftdi_sio.c: Detected FT232BM
usb 1-1: FTDI USB Serial Device converter now attached to ttyUSB0
usbcore: registered new driver ftdi_sio
drivers/usb/serial/ftdi_sio.c: v1.4.3:USB FTDI Serial Converters Driver
So your smartreader+ is ready to update the firmware.

4: Uptate beginning.
Copy to your PC linux server FTP 2 files:
srp_tools_x86
srp_update_x86
Set on console to both file chmod 755 !

Chek if your smartreader+ needs to update.
Run command: ./srp_update_x86
and you see like so:
smartreader+ version v1.0, v1.1 or v1.2 then you have time to update.

5: Upadte. I DO NOT RESPONSIBLE IF SOMHTING GOES WRONG WITH FLASH!
Run command: ./srp_update_x86 -b
smartreader+ version v1.1
bootloader mode activated
Remove and reinsert SmartReader+ then restart application

Then new command: ./srp_update_x86 -f
start flashing
################################################## ######## done
Please remove and reinsert SmartReader+

remove the reader and reinsert now we start the config tool
Run command: ./srp_tools_x86
smartreader+ version v1.3
MODE autoswitch
FREQ 3.69 Mhz
KERNEL normal
T_MODE t = 0
EGT 0

successfully flashed the reader with new firmware.

Now we need add to CCcam.cfg new line:
SERIAL READER : /dev/ttyUSB0 smartreader+
SERIAL READER : /dev/ttyUSB1 smartreader+
SERIAL READER : /dev/ttyUSB2 smartreader+
or whatever USB port your smartreader is entered.
Save CCcam.cfg and run ./CCcam.x86 -d you should see new card is added and running.
In CCcam.cfg is card overklocking and there you just edit like so:
SMARTCARD CLOCK FREQUENCY: /dev/ttyUSB0 4800000 and card works with 4.80mhz set by smartreader+.
Available frequencies

3.20, 3.43, 3.69, 4.00, 4.36, 4.80, 5.34, 6.00, 6.86, 8.00, 9.61, 12.0 and 16.0 MHz

The user can selected any freqency. The Smartreader+ will selected the nearest available.
Default sartreader+ speed is with new v1.3 firmware 3.69MHZ and most cards works with that speed.

And more configuratsion options you will find inside smartreader_v103.zip.
------------------------------
Dreambox 800HD + interne HD  80 giga, Triax 88 cm, 4 LNB multifeed, Samsung 40 inch Full HD LCD TV@100Hz, MacMini 2Ghz

LuxSat Satellite  |  Satelliet Programmer  |  Software  |  Waar kan ik de driver voor een smargo usb smartreader vinden aub?
 

gfxgfx
gfx gfx